Tecno Spark Go 2020 KE5S Firmware

Last Updated: May 8, 2026

---

Tecno Spark Go 2020 KE5S Firmware (Flash File) Drivers, Tools & Guide

I have worked on Tecno phones for a while and the KE5S Spark Go 2020 is one I see often. It usually arrives with FRP locks, bootloops, or stuck on the Tecno logo. This guide covers all of it. I have put everything you need in one place: the firmware, the tools, and the exact process I use myself.

One thing I always recommend before you start: extract the firmware to a simple folder path, something like C:FirmwareKE5S. SP Flash Tool can sometimes have trouble locating the scatter file if the folder path contains spaces or special characters. It is a small thing, but it saves a frustrating few minutes of wondering why the tool is not loading the file.

Your Tecno Spark Go 2020 KE5S firmware comes as a compressed ZIP file. Download and extract it using WinRAR or 7-Zip. Once extracted, open the folder and confirm it contains the scatter file before proceeding.

Flash the stock firmware to resolve software issues, including FRP lock, app problems, slow performance, forgotten pattern locks, a dead or logo-stuck device, Wi-Fi and Bluetooth issues, battery drain, and soft brick situations. Note that this process erases all data.

---

Hard Reset Tecno Spark Go 2020 KE5S

To factory reset Tecno Spark Go 2020 KE5S without a computer, power off the device completely, then hold Volume Up and Power at the same time until the recovery menu appears. Use the volume keys to navigate to “Wipe Data/Factory Reset” and confirm with the Power button.

A hard reset erases all data and restores Tecno Spark Go 2020 KE5S to its original factory state. This fixes most software problems, slow performance, app crashes, forgotten screen locks, and bootloops. If the issue persists after a factory reset, a full firmware flash using SP Flash Tool is covered in the following sections.

---

Tecno Spark Go 2020 KE5S FRP Bypass

The fastest way to bypass FRP on Tecno Spark Go 2020 KE5S is to use a free Android apps launcher that lets you access settings during the setup wizard. After flashing or performing a factory reset you may see a Google account lock (FRP). Our free Android apps launcher is the fastest way to get past it. This is also why I always recommend removing your Google account before flashing, it avoids this problem entirely.

---

Why Do We Need Tecno Spark Go 2020 KE5S Firmware?

The Tecno Spark Go 2020 KE5S uses a MediaTek chipset, and SP Flash Tool is the standard method for firmware recovery on MTK devices. Here is what flashing the stock firmware can help with:

• Unlock your device if it has been locked or disabled.
• Update to the latest Android version supported by your phone.
• Fix startup loops, lagging, and freezing on your KE5S Spark Go 2020.
• Resolve OTA update failures and battery drain issues.
• Restore the original Tecno stock ROM to keep your warranty valid.
• Recover your device when it only boots into recovery mode.
• Recover from “Download DA FAIL” errors and Secure Boot authentication issues specific to the MediaTek chipset in your device.

Learn more about stock ROMs and why flashing works.

---

Choosing the Right Firmware Version

Before you begin flashing, take a moment to confirm you have the right file. Flashing the wrong firmware is a mistake that is difficult to recover from:

1. Identify Your Device Model: Go to About Phone and confirm your model is Tecno Spark Go 2020 KE5S. Check the full model string, not just the name.
2. Verify the Build Number: Look for the identifier “KE5S” in your device build details.
3. Confirm the Chipset: According to Tecno specifications, the Spark Go 2020 KE5S runs on MediaTek MT6761D Helio A20.
4. Match the Firmware Version: Check the version and regional details against what is listed in the download table above.
5. Verify in Recovery Mode: If you are not sure about the chipset or build number, boot into recovery mode, it displays this information clearly and is the most reliable way to confirm before you flash.

---

Firmware Details for Tecno Spark Go 2020 KE5S

Here is a quick overview of the official firmware specifications:

Firmware Information	Details
Device Model	Tecno Spark Go 2020 KE5S
Firmware Version	V035, V194, V145, V140
File Size	8.96 MB to 1.6 GB
Android Version	Android 10 (Go edition), HIOS 6.2
Platform	MediaTek MT6761D Helio A20
Release Date	Released 2020, September 07
Region	Global, Africa and Asia
File Type	ZIP (Includes Scatter File [MT6xxx_Android_scatter.txt], preloader.bin, boot.img, system.img, recovery.img, lk.bin, logo.bin, nvram.img, and more)

---

Which Firmware Version Should I Download?

This is the question I get asked most often in the comments, so I put together a simple guide. Find your situation in the table and go straight to the right file:

Your Situation	What I Recommend
Phone is completely dead or stuck on logo	V194, download this one. It is the latest Tecno Spark Go 2020 KE5S firmware available.
FRP / Google account lock only	See the FRP bypass guide above, you likely do not need the full firmware for this.
Phone slow after a recent OTA update	Try V145, sometimes the latest OTA introduces new bugs and an older build runs better.
IMEI missing after a previous flash	Re-flash V194 first, then follow the IMEI repair guide. Do not skip the reflash.
V194 failed with a flash error	Try V145 instead and double-check your scatter file selection before assuming the firmware is the problem.
Restoring to factory / warranty repair	V194, clean state, fresh start.

My general approach with MTK devices: always try the latest version first. I have seen people spend a lot of time trying older builds when the newest one would have worked fine. Only move to an older version if the latest fails more than once, and make sure it is a driver issue you are solving, not a firmware issue.

---

Download Tecno Spark Go 2020 KE5S Firmware

Download the official stock firmware for your Tecno Spark Go 2020 KE5S below. The latest available version is V194. After downloading, verify the file size matches the table above, a size mismatch usually means a partial or corrupt download, and flashing a corrupt file can cause more problems than it solves.

Software Details	Download Link	Members Link
File Name: Tecno_Spark_Go_2020_KE5S_MT6761_V035_201203.zip Size: 1.6 GB	Download Link	Download Link2

File Name: Tecno_Spark_Go_2020_KE5S_MT6761_V035.zip Size: 1.6 GB

Download Link

Download Link2

File Name: KE5.rar Size: 8.96 MB

Download Link

Download Link2

File Name: Ke5k_V194_boot_vbmeta_files.rar Size: 9.29 MB

Download Link

Download Link2

File Name: Tecno Spark Go 2020 (KE5-H6123ABC-QGo-GL-200916V145) [Factory / Signed] Size: N/A

Download Link

Download Link2

File Name: Tecno Spark Go 2020 (KE5-H6123ABC-QGo-GL-200909V140) [Factory / Signed] Size: N/A

Download Link

Download Link2

Only download firmware that is fully compatible with your exact device model. See the firmware selection guide above if you are not sure.

---

Prerequisites for Tecno Spark Go 2020 KE5S Firmware

Do not skip this section. Most failed Tecno flashes come from rushing through the preparation steps. The VCOM driver installation is essential for the Tecno Spark Go 2020 KE5S and other MediaTek devices. Windows may show the device in Device Manager and SP Flash Tool will still not detect it if the correct VCOM driver is not installed.

1. Back Up IMEI Numbers: Dial *#06# and write down both IMEI numbers now. You will need these if you need to restore your IMEI after flashing.
2. Remove Google Accounts: Sign out of all Google accounts to prevent FRP lock after flashing.
3. Back Up Your Data: Back up everything, photos, contacts, WhatsApp chats, important files. Flashing wipes the device completely.
4. Charge Your Device: At least 50% battery. A device that powers off during a flash is very difficult to recover.
5. USB Cable & PC: Use a proper data USB cable, not a charge-only cable, and a Windows computer with available USB ports.
6. Install Required Drivers:
   • VCOM Drivers
   • Tecno USB Drivers

---

How to Install Firmware on Tecno Spark Go 2020 KE5S

We are using SP Flash Tool for this. For older devices, I recommend trying SP Flash Tool v5.1924 first. The newer versions of SP Flash Tool require a DA (Download Agent) file that older firmware packages do not include, and that is what causes the “Auth” errors you may have seen. If SP Flash Tool keeps asking for an auth file and you do not have one, switch to MTK Client, it handles Secure Boot automatically. Download SP Flash Tool for Windows or SP Flash Tool for Linux and follow the steps below. The complete SP Flash Tool guide is also available if you need more detail.

1. Download and Extract:
   • Download the correct firmware package from the links above.
   • Extract the ZIP to a simple folder path, avoid paths with spaces or special characters, as some flash tools have trouble with them.
2. Install the Listed Drivers:
   • Confirm all drivers listed above are installed and that your PC has been restarted since installation. Skipping the restart is a common reason drivers do not work correctly.
3. Load the Firmware File:
   • Click on the “Scatter-loading” button. Navigate to the folder where you extracted the firmware and select the “scatter.txt” file.
4. Connect Your Device:
   • Power off your phone completely, not sleep mode, fully off.
   • Connect to your PC via USB cable. The flash tool will detect it automatically.
5. Start Flashing:
   • Click the “Download” button to begin.
   • Do not disconnect, move the cable, or touch the device until the process is fully complete. Disconnecting mid-flash is how devices get bricked.
6. Wait and Reboot:
   • Once flashing finishes successfully, disconnect the device.
   • Power on your device. The first boot will take longer than usual, give it up to 8 minutes.

---

What to Expect After Flashing Tecno Spark Go 2020 KE5S Firmware

I get a lot of comments from people who think something went wrong when it actually did not. Here is what is completely normal after a successful Tecno Spark Go 2020 KE5S firmware flash:

• How to know the flash was successful: SP Flash Tool will show a green circle or checkmark when done. If you see that, the flash completed successfully.
• First boot takes 3 to 8 minutes, do not force-reboot the device. The operating system is setting itself up from scratch. Interrupting this is how devices end up in bootloops.
• The phone will feel warm during first boot, this is normal. It settles after a few minutes once the initial app setup is complete.
• All your apps are gone, this is expected. Reinstall them from the Play Store. If you had a Google account backup active, it will offer to restore your apps automatically during setup.
• Dial *#06# immediately after setup to check your IMEI. Do this before you insert a SIM card. If it shows “unknown” or “null”, follow the IMEI repair guide below before doing anything else.
• Be careful when re-adding your Google account, if you did not remove it before flashing, you may see an FRP prompt. Add it fresh during the setup wizard, not afterwards through Settings.
• Wi-Fi, Bluetooth, and mobile data should all work right after setup. If mobile data is not connecting, go to Settings › SIM and Network and re-enter your APN manually, the flash sometimes clears carrier APN settings.
• Stuck in a bootloop after first boot? Enter recovery mode and do a factory reset from there, see the hard reset guide above. This can happen occasionally and does not mean the firmware is wrong, it is usually a conflict with leftover data from the old install.

• HiOS / XOS Pre-installed Apps: After flashing Tecno Spark Go 2020 KE5S firmware, you will see pre-installed apps from Tecno. These can be disabled in Settings › Apps if you do not want them, but do not force-remove them with ADB, as some are tied to system services on your device.

---

Missing IMEI or Corrupt Baseband on Tecno Spark Go 2020 KE5S After Flashing?

A missing or unknown IMEI is one of the most common things I see after a MediaTek flash. It happens because the NVRAM partition, which stores your IMEI and calibration data, sometimes does not survive the flash intact. It looks alarming, but it is fixable. Here is what to do:

1. Check your drivers first: Install the Mediatek CDC Driver if you have not already, without it, the IMEI repair tools will not detect your device. This is the step most people miss.
2. Use SN Write Tool or Maui Meta: SN Write Tool is the first option I try, it is straightforward and works on most MTK devices. Maui Meta is the alternative if SN Write does not connect. You can learn more about using SN Write Tool here.
3. Run the repair:
   • Connect your device to the computer.
   • Enter the original IMEI numbers for both SIM slots, these are the numbers you wrote down before flashing.
   • Click “Start” and let it complete without interrupting the connection.
4. Verify after reboot: Once done, reboot your phone and dial *#06#. Your IMEI numbers should be back. If they are still showing null, run the process again, sometimes the first attempt does not complete correctly.

Video Guide: How to repair IMEI

Credits: https://www.youtube.com/@mhgsmclinic

---

Common Issues When Flashing Tecno Spark Go 2020 KE5S

1. Tecno Spark Go 2020 KE5S Not Recognized by SP Flash Tool:
   • In most cases this is a driver issue, not a cable issue. Reinstall the VCOM drivers for the KE5S, restart your PC, and try again before changing anything else.
   • If that does not work, switch to a USB 2.0 port, USB 3.0 ports can cause detection issues with MediaTek devices more often than people expect.
   • Still not working? Temporarily disable your antivirus. It can block the VCOM driver from loading without giving you any error message.
2. Boot Loop After Flashing:
   • Enter recovery mode and perform a factory reset from there. Most post-flash bootloops on MediaTek are caused by conflicts with old cached data, a wipe from recovery usually fixes this without needing to reflash.
3. Wrong Scatter File / Firmware Mismatch:
   • If SP Flash Tool throws an error as soon as you try to start the download, check your scatter file first. A mismatch between the scatter file and your device build is one of the most common causes of flash errors.
4. “Download DA FAIL” Error:
   • This error comes up regularly. It almost always means the VCOM driver is not properly installed. Reinstall it, restart your PC, and try again. If that still does not work, try switching to SP Flash Tool v5.1924, older devices sometimes respond better to the older version.
5. Error 8038 (BROM Error):
   • The device is not entering BROM mode correctly. Power it off completely and, if possible, remove the battery for 30 seconds. Reconnect and try again. Some MediaTek devices require you to hold Volume Down while plugging in the USB cable to enter BROM mode.
6. Auth File / Secure Boot Error in Newer SP Flash Tool:
   • Newer versions of SP Flash Tool require a DA (Download Agent) authentication file for devices with Secure Boot enabled. If you do not have that file, switch to MTK Client instead, it handles Secure Boot automatically and is the simpler solution.

---

Frequently Asked Questions

Q1: Will flashing the Tecno Spark Go 2020 KE5S firmware erase my data?
A: Yes, flashing this firmware with SP Flash Tool restores your device to factory state, including Android 10 (Go edition), HIOS 6.2 default settings. All apps, photos, contacts, and accounts will be removed. Back up everything you need before you start. There is no way to recover data once the flash is complete.

Q2: Is this firmware compatible with other Tecno models?
A: No. This firmware is built specifically for the Tecno Spark Go 2020 KE5S running on the MediaTek MT6761D Helio A20 chipset. Even the Spark Go 2020 with a different letter suffix (for example, a different variant of KE5S) can have a completely different chipset inside. Flashing the wrong firmware can leave your phone in a state that is very difficult to recover from. Always check your exact model number in Settings › About Phone.

Q3: Can I downgrade from V194 to an older firmware version?
A: It is technically possible on some MediaTek builds, but I do not recommend it. Downgrading can cause security issues and app compatibility problems on Android 10 (Go edition), HIOS 6.2. If V194 is causing you trouble, leave a comment below, there is usually a better fix than rolling back.

Q4: What should I do if I encounter an FRP lock after flashing?
A: Use our free Android apps launcher. FRP lock on the Tecno Spark Go 2020 KE5S activates when a Google account was still signed in before flashing. This is also why I always recommend signing out of your Google account before flashing, it avoids this issue entirely.

Q5: Are custom ROM options available for the Tecno Spark Go 2020 KE5S?
A: This guide covers official Tecno stock firmware only. Custom ROM availability for the Tecno Spark Go 2020 KE5S depends on whether the MediaTek MT6761D Helio A20 chipset has open-source kernel support. Check our Custom ROMs page or the XDA Developers forum for device-specific custom ROM threads.

Q6: My Tecno Spark Go 2020 KE5S is not detected by SP Flash Tool. What should I do?
A: Start with the drivers, reinstall the VCOM drivers, restart your PC, then try again. Switch to a USB 2.0 port if you are on USB 3.0, MTK devices are more reliable on USB 2.0 ports. Disable your antivirus temporarily. If none of that works, leave a comment below with the exact error message and I will help you from there.

Q7: How do I enter recovery mode on my Tecno Spark Go 2020 KE5S?
A: Power the device off completely, then hold Volume Up + Power at the same time until the recovery menu appears. The recovery menu will display the build number for your Tecno Spark Go 2020 KE5S which you can use to verify your firmware version before flashing.

Q8: My IMEI shows “unknown” after flashing the Tecno Spark Go 2020 KE5S. Is my phone permanently damaged?
A: No, it looks alarming, but it is fixable. Follow the IMEI repair guide in the troubleshooting section above. For MediaTek devices, SN Write Tool or Maui Meta will handle the repair. The important thing: do not insert a SIM card until the IMEI is restored.

Q9: How long does it take to flash Tecno Spark Go 2020 KE5S firmware?
A: The actual flashing process usually takes between 3 and 10 minutes depending on the firmware size and your USB connection speed. The first boot after flashing takes longer, anywhere from 3 to 8 minutes. Do not interrupt the device during either stage. If the progress bar in SP Flash Tool appears stuck, give it a few more minutes before assuming something went wrong.

---

Final Thoughts on Tecno Spark Go 2020 KE5S Firmware

That is everything you need to safely flash the official Tecno Spark Go 2020 KE5S firmware (V194) using SP Flash Tool and get your device working again. If you followed each step, your phone should now be running on a clean build.

If something did not go as expected, a specific error, a step that is not working for your setup, leave a comment below with as much detail as you can: the exact error message, which step you are on, and what you have already tried. I read every comment and will help you work through it.

If this guide helped you, consider sharing it, it is the best way to help someone else who is dealing with the same problem.

Browse all Tecno firmware downloads for more devices.

---

Disclaimer: Flashing stock firmware is performed at your own risk. Follow the instructions on this page carefully. I cannot be held responsible for any damage to your device, but I will always try to help if something goes wrong.