Last Updated: July 19, 2026
This page provides everything needed for Tecno Pop 5 BD2p firmware: official stock ROM downloads, required drivers, and detailed instructions to resolve bootloops, remove FRP locks, or perform a clean reinstallation.
Device: Tecno Pop 5 BD2p | Chipset: Unisoc Spreadtrum SC7731E | Flash Tool: SPD Research Tool
Android: Android 10 (Go edition), HIOS | File Type: ZIP (Contains .pac firmware file for SPD Research Tool)
⚠ Warning: Flashing erases all data. Back up first.
Device: Tecno Pop 5 BD2p (Unisoc Spreadtrum SC7731E)
Flash Tool: SPD Research Tool
Latest Build: V18
Firmware Files: 21 available
What You Need: Windows PC, USB data cable, SPD Research Tool, USB drivers
Time Required: 10-20 minutes (plus 3-8 min first boot)
Tecno Pop 5 BD2p Firmware (Flash File) Drivers, Tools & Guide
The Tecno Pop 5 BD2p firmware requires specific procedures due to its Unisoc Spreadtrum architecture. Most flashing errors occur when users select incompatible .pac files. This guide provides verified firmware, correct tools, and precise steps to avoid common pitfalls.
Before proceeding, note that Unisoc firmware packages contain a single .pac file, unlike MediaTek devices which use partition folders. Always confirm your ZIP contains the .pac file before opening SPD Research Tool. Partial downloads often cause unnecessary delays.
This page lists 21 official firmware builds for the Tecno Pop 5 BD2p, covering multiple Android versions and security patches. The stock firmware runs Android 10 (Go edition) with HIOS. As a Unisoc SC7731E device, it requires SPD Research Tool and dedicated USB drivers—these won’t work with MediaTek or Qualcomm chipsets.
All firmware files were verified across three independent sources to ensure authenticity. As part of Transsion Holdings’ ecosystem, Tecno devices share similar flashing protocols across the Pop 5 series.
Download the Tecno Pop 5 BD2p firmware ZIP and extract it using WinRAR or 7-Zip. After extraction, verify the .pac file exists in the folder before continuing.
Flashing restores the device to factory settings, which resolves persistent issues like bootloops, screen locks, battery drain, and system errors. This clean wipe permanently deletes all personal data.
Hard Reset Tecno Pop 5 BD2p
To factory reset the Tecno Pop 5 BD2p without a computer, power off the device completely. Then hold Volume Up and Power simultaneously until the recovery menu appears. Navigate to “Wipe Data/Factory Reset” using volume keys and confirm with the Power button.
A hard reset erases all data and returns the Tecno Pop 5 BD2p to its original factory state. This resolves most software problems including slow performance, app crashes, forgotten screen locks, and bootloops. If issues persist after reset, proceed with full firmware flashing using SPD Research Tool.
Remove FRP Lock on Tecno Pop 5 BD2p
The fastest method to bypass FRP on Tecno Pop 5 BD2p involves using a free Android apps launcher to access settings during setup. After flashing or factory reset, you may encounter a Google account lock (FRP). Our free Android apps launcher provides the quickest solution. Always remove Google accounts before flashing to prevent this issue.
Common Reasons to Reinstall Tecno Pop 5 BD2p Firmware
The most reliable solution for software issues on Unisoc devices like the Tecno Pop 5 BD2p is a clean firmware flash using SPD Research Tool. Stock firmware resolves these problems:
- Fix startup loops, lagging, and freezing issues.
- Restore original Tecno stock ROM to maintain warranty validity.
- Resolve touchscreen problems caused by corrupted system files.
- Clear forgotten screen locks, PIN, or pattern without credentials.
- Resolve OTA update failures and battery drain issues.
- Fix Wi-Fi, Bluetooth, or mobile data connectivity problems.
- Resolve .pac loading errors in SPD Research Tool that prevent normal operation.
Learn more about stock ROMs and why flashing works.
Choosing the Right Firmware Version
The most frequent error is flashing firmware for a different device variant. Before downloading, verify your exact device identity:
- Identify Your Device Model: Confirm “Tecno Pop 5 BD2p” in Settings > About Phone. Check the full model string, not just the name.
- Verify the Build Number: Look for “BD2p” in your device build details.
- Confirm the Chipset: The Pop 5 BD2p uses Unisoc Spreadtrum SC7731E according to specifications.
- Match the Firmware Version: Compare version and regional details with the download table.
- Verify in Recovery Mode: Boot into recovery mode (Volume Up + Power while off) to reliably confirm chipset and build number before flashing.
Firmware Details for Tecno Pop 5 BD2p
Official firmware specifications for the Tecno Pop 5 BD2p:
| Firmware Information | Details |
|---|---|
| Device Model | Tecno Pop 5 BD2p |
| Firmware Version | V2, V4, V6, V8, V10, V12, V14, V17, V18, V15, V5 |
| File Size | 1.4 GB to 1.95 GB |
| Android Version | Android 10 (Go edition), HIOS |
| Platform | Unisoc Spreadtrum SC7731E |
| Release Date | Released 2021, July 26 |
| Region | Global, Africa and Asia |
| File Type | ZIP (Contains .pac firmware file for SPD Research Tool) |
Which Firmware Version Should I Download?
Based on common scenarios, this guide recommends appropriate firmware versions:
| Your Situation | What I Recommend |
|---|---|
| Phone is completely dead or stuck on logo | V18, this is the latest Tecno Pop 5 BD2p firmware available. |
| FRP / Google account lock only | See the FRP bypass guide above, you likely do not need full firmware for this. |
| Phone slow after recent OTA update | Try V17, latest OTAs sometimes introduce bugs; older builds perform better. |
| IMEI missing after previous flash | Re-flash V18 first, then follow the IMEI repair guide. Do not skip reflash. |
| V18 failed with flash error | Try V17 instead and verify .pac file selection before blaming firmware. |
| Restoring to factory / warranty repair | V18, provides clean state and fresh start. |
For Unisoc devices, always try the latest .pac file first. Older SPD Research Tool firmware versions may cause modem issues, resulting in no signal after flashing. Use older versions only if the latest fails.
Download Tecno Pop 5 BD2p Firmware
Download official stock firmware for the Tecno Pop 5 BD2p below. The latest version is V18. After downloading, confirm the file size matches the table above, size discrepancies usually indicate corrupt downloads, which cause more problems than they solve.
| Software Details | Download Link | Members Link |
|---|---|---|
|
File Name: Tecno_Pop_5_BD2P_V2_210416_SPD.zip Size: 1.8 GB | Download Link | Download Link2 |
| File Name: Tecno_Pop_5_BD2P_V4_210509_SPD.zip Size: 1.8 GB | Download Link | Download Link2 |
| File Name: Tecno_Pop_5_BD2P_V6_210619_SPD.zip Size: 1.8 GB | Download Link | Download Link2 |
| File Name: Tecno_Pop_5_BD2P_V8_210825_SPD.zip Size: 1.9 GB | Download Link | Download Link2 |
| File Name: Tecno_Pop_5_BD2P_V10_220117_SPD.zip Size: 1.9 GB | Download Link | Download Link2 |
| File Name: Tecno_Pop_5_BD2P_V12_220511_SPD.zip Size: 1.9 GB | Download Link | Download Link2 |
| File Name: Tecno_Pop_5_BD2P_V14_220921_SPD.zip Size: 1.9 GB | Download Link | Download Link2 |
| File Name: Tecno_Pop_5_BD2P_V17_230202_SPD.zip Size: 1.9 GB | Download Link | Download Link2 |
| File Name: BD2p-SP613DEF-RGo-OP-230419V18.zip Size: 1.89 GB | Download Link | Download Link2 |
| File Name: BD2p-SP613DEF-RGo-OP-230202V17.zip Size: 1.9 GB | Download Link | Download Link2 |
| File Name: BD2p-SP613DEF-RGo-OP-221116V15.zip Size: 1.91 GB | Download Link | Download Link2 |
| File Name: BD2p-SP613DEF-RGo-OP-220921V14.zip Size: 1.91 GB | Download Link | Download Link2 |
| File Name: BD2p-SP613DEF-RGo-OP-220511V12.zip Size: 1.95 GB | Download Link | Download Link2 |
| File Name: BD2p-SP613DEF-RGo-OP-220117V10.zip Size: 1.87 GB | Download Link | Download Link2 |
| File Name: BD2p-SP613DEF-RGo-OP-210825V8.zip Size: 1.88 GB | Download Link | Download Link2 |
| File Name: BD2p-SP613DEF-RGo-OP-210619V6.zip Size: 1.85 GB | Download Link | Download Link2 |
| File Name: BD2p-SP613DEF-RGo-OP-210509V4.zip Size: 1.86 GB | Download Link | Download Link2 |
| File Name: BD2p-SP613DEF-RGo-OP-210416V2.zip Size: 1.87 GB | Download Link | Download Link2 |
| File Name: Tecno POP 5 (BD2p-SP613DEF-RGo-OP-210522V5).7z Size: 1.4 GB | Download Link | Download Link2 |
| File Name: Tecno POP 5 (BD2p-SP613DEF-RGo-OP-210416V2).7z Size: 1.4 GB | Download Link | Download Link2 |
| File Name: Tecno POP 5 (BD2p-SP613DEF-RGo-OP-210825V8).7z Size: 1.4 GB | Download Link | Download Link2 |
Only download firmware compatible with your exact device model. See the firmware selection guide above if you are unsure.
Important: The Tecno Pop 5 BD2p (BD2p) should not be confused with other Pop 5 variants that may have different chipsets or regional firmware. Even devices in the same Pop 5 line can use completely different processors. Always verify your exact model code “BD2p” in Settings > About Phone before downloading any firmware from this page.
- Your model number is a variant of BD2p with a different letter suffix. Check About Phone carefully, one letter difference can cause a failed or broken flash.
- Your chipset differs from Unisoc Spreadtrum SC7731E. Confirm in recovery mode before proceeding.
- You downloaded the file from a source other than this page.
- The file size differs significantly from the sizes listed in the table above, a size mismatch usually means a partial download, which will fail mid-flash.
Before You Start: Tecno Pop 5 BD2p Requirements
Before downloading any Tecno Pop 5 BD2p firmware, complete this checklist. The most common cause of Unisoc flashing failures is missing drivers. SPD Research Tool requires specific drivers that Windows may not always detect.
- Back Up IMEI Numbers: Dial *#06# and record both IMEI numbers now. You will need these if IMEI restoration is required after flashing.
- Remove Google Accounts: Sign out of all Google accounts to prevent FRP lock after flashing.
- Back Up Your Data: Back up all content, photos, contacts, WhatsApp chats, important files. Flashing wipes the device completely.
- Charge Your Device: Maintain at least 50% battery. A device powering off during flash is difficult to recover.
- USB Cable & PC: Use a proper data USB cable, not charge-only, and a Windows computer with available USB ports.
- Install Required Drivers:
- Tecno USB Drivers (includes Spreadtrum USB drivers)
Step-by-Step: Flash Tecno Pop 5 BD2p Stock ROM
We use SPD Research Tool for this process—the standard tool for Unisoc devices. Always run it as Administrator: right-click the .exe and select “Run as administrator” to avoid permission errors. The video guide below demonstrates the process if you prefer visual instructions.
- Prepare the Flash Files:
- Download the firmware package matching your device from the download section.
- Extract the ZIP to a desktop folder. Avoid non-English characters or spaces in folder names—the tool may not read them correctly.
- Confirm Driver Setup:
- Install and test the drivers listed in prerequisites before connecting the phone. If unsure, reinstall and restart your computer.
- Load the Firmware File:
- Click “Load Packet” and select the .pac file from the extracted folder.
- Connect Your Device:
- Power off your phone completely, not sleep mode, fully off.
- Connect to your PC via USB cable. The flash tool will detect it automatically.
- Start Flashing:
- Click “Start” to begin the firmware write.
- Do not touch the phone or cable until the tool shows completion. Disconnecting mid-flash is the most common cause of bricked devices.
- Wait and Reboot:
- When you see the success message, disconnect the USB cable.
- Hold the power button to boot the phone. Allow 5-8 minutes for first startup, this is normal.
Video Guide for Flashing
Normal Behavior After Installing Tecno Pop 5 BD2p Firmware
Expected behavior after a successful flash:
- Successful flash confirmation: SPD Research Tool displays a green “PASSED” message when complete.
- Post-flash bootloop: Enter recovery mode and perform a factory reset, see the hard reset guide above. This occasionally occurs and does not indicate faulty firmware.
- Connectivity restoration: Wi-Fi, Bluetooth, and mobile data should work after setup. If mobile data fails, manually re-enter APN in Settings > SIM and Network, flashing sometimes clears carrier settings.
- IMEI verification: Dial *#06# immediately after setup. Check for “unknown” or “null” IMEI before inserting a SIM. If present, follow the IMEI repair guide immediately.
- Google account handling: Add accounts fresh during setup wizard if not removed before flashing. Adding through Settings later may trigger FRP.
- First boot temperature: The phone may feel warm during initial boot, this normalizes once setup completes.
- Sound settings reset: Ringtones and notification sounds return to factory defaults. Custom tones require re-download and reassignment.
Tecno Pop 5 BD2p Flashing Problems and Fixes
- Tecno Pop 5 BD2p Not Recognized by SPD Research Tool:
- This is typically a driver issue, not a cable problem. Reinstall Spreadtrum USB drivers for the BD2p, restart your PC, and retry.
- If still undetected, try a USB 2.0 port, these work more reliably with Unisoc devices than USB 3.0.
- Temporarily disable antivirus software, it may block Spreadtrum driver loading without showing errors.
- Boot Loop After Flashing:
- Enter recovery mode and perform a factory reset. This resolves most post-flash bootloops on Unisoc devices. If recovery is inaccessible, reflash from scratch.
- Wrong .pac File Selected for BD2p:
- SPD Research Tool errors immediately after loading indicate incorrect firmware. Confirm the .pac file model code exactly matches your Tecno Pop 5 BD2p.
- No Signal After Flashing:
- This usually indicates IMEI issues. Dial *#06#, if it shows null or unknown, repair IMEI before using the SIM card.
Missing IMEI or Corrupt Baseband on Tecno Pop 5 BD2p After Flashing?
A missing IMEI after Unisoc flashing usually means the NVRAM partition didn’t write correctly. This occurs frequently on SPD devices. Use the WriteIMEI Tool for Unisoc to restore it. Ensure you have the original IMEI recorded from before flashing, dial *#06# beforehand. Without the original number, proper restoration is impossible.
Use WriteIMEI Tool for Unisoc for restoration. The video guide below demonstrates the exact steps.
Video Guide: How to repair IMEI
Questions About Tecno Pop 5 BD2p Firmware
Q1: Is this firmware compatible with other Tecno models?
A: No. This firmware is specifically for the Tecno Pop 5 BD2p with Unisoc Spreadtrum SC7731E chipset. Even Pop 5 variants with different letter suffixes may have different chipsets. Flashing incompatible firmware can leave your device unrecoverable. Always verify your exact model number in Settings.
Q2: My IMEI shows “unknown” after flashing. Is my phone permanently damaged?
A: No, this is alarming but fixable. Follow the IMEI repair guide above. For Unisoc devices, use the WriteIMEI Tool. Do not insert a SIM card until IMEI is restored.
Q3: Can I flash this firmware if my phone does not turn on at all?
A: Yes, in most cases. As long as the phone responds to USB connection (even with a black screen), the flash tool detects it. If the battery is completely drained, charge it for at least 15 minutes first.
Q4: Do I need an internet connection during flashing?
A: No. The flashing process is entirely offline between PC and phone via USB. You need internet later for app setup and downloads.
Q5: How long does the flashing process take?
A: Actual flashing takes 3-10 minutes depending on firmware size and USB speed. First boot requires another 3-8 minutes. Do not interrupt either stage. If SPD Research Tool progress appears stuck, wait several minutes before assuming failure.
Q6: How do I enter recovery mode?
A: Power off completely, then hold Volume Up + Power simultaneously until recovery menu appears. The recovery display shows build number to verify firmware version before flashing.
Q7: Will flashing erase my data?
A: Yes, flashing with SPD Research Tool performs a full factory reset including Android 10 (Go edition) and HIOS defaults. All apps, photos, contacts, and accounts are removed. Back up everything before starting. Data cannot be recovered after flashing.
Q8: What should I do if I encounter an FRP lock after flashing?
A: Use our free Android apps launcher. FRP activates when a Google account remains signed in before flashing. This is why signing out before flashing prevents the issue.
People Also Ask About Tecno Pop 5 BD2p
Will flashing firmware on Tecno Pop 5 BD2p erase my data?
Yes. Flashing stock firmware on the Tecno Pop 5 BD2p with SPD Research Tool performs a full factory reset. All apps, photos, contacts, and accounts will be removed. Back up everything important before you start. There is no way to recover data after flashing.
How do I check my Tecno Pop 5 BD2p model number before flashing?
Go to Settings > About Phone on your Tecno Pop 5 BD2p and look for the model number “BD2p”. You can also confirm by entering recovery mode (Volume Up + Power while powered off) which displays the build number and model code. Always match this exactly with the firmware filename before flashing.
Can flashing firmware fix a bricked Tecno Pop 5 BD2p?
Yes. If your Tecno Pop 5 BD2p is stuck on the logo, in a bootloop, or will not turn on, flashing the stock firmware with SPD Research Tool can restore it to working condition. This is the standard repair method used by service centers for Tecno devices.
What chipset does the Tecno Pop 5 BD2p use?
The Tecno Pop 5 BD2p runs on the Unisoc Spreadtrum SC7731E, a Unisoc (Spreadtrum) processor. You will need SPD Flash Tool (also called SPD Research Tool) and SPD USB drivers to flash firmware on this device.
Summary
You have successfully completed a clean firmware flash on your Tecno Pop 5 BD2p. The device should now be at the setup wizard on a fresh V18 build.
Questions, errors, or unresolved issues? The comments section is open. Describe exactly what happened, and I will guide you through the solution.
If this guide helped you, sharing it assists others with the same device who may be searching for this solution.
Browse all Tecno firmware downloads for additional devices.
Disclaimer: Flashing stock firmware is performed at your own risk. Follow instructions carefully. I cannot be held responsible for device damage, but I will assist if problems arise.
