Tecno Pop 1s Firmware

Last Updated: September 8, 2026

The Tecno Pop 1s is a common repair case. It usually arrives with bootloops, FRP issues, or a stuck logo. This guide provides the official firmware, tools, and steps to get it working again.

---

Tecno Pop 1s Firmware (Flash File) Drivers, Tools & Guide

Extract the firmware to a simple folder path, such as C:Firmware. SP Flash Tool often struggles with paths containing spaces or special characters, so a clean path prevents loading errors.

Only one official firmware build exists for the Tecno Pop 1s. Released in 2018, this stock ROM is for Android 8.1 Oreo (Go edition). USB driver compatibility on newer Windows versions (10/11) typically requires manual installation rather than automatic detection.

Download and extract the firmware using WinRAR or 7-Zip. Open the folder and confirm the scatter file is present before proceeding.

A full firmware flash wipes all data: apps, accounts, photos, and settings. This restores a clean slate and resolves issues like screen locks, FRP prompts, dead boot states, sluggish performance, and connectivity problems.

---

Reset Tecno Pop 1s From Recovery Mode

Power off the device completely, then hold Volume Up and Power until the recovery menu appears. Navigate to “Wipe Data/Factory Reset” and confirm with the Power button.

A hard reset erases all data and restores the phone to its original factory state. This fixes most software problems, including slow performance, app crashes, forgotten screen locks, and bootloops. If the issue persists after a factory reset, a full firmware flash is required.

---

Bypass Google Lock on Tecno Pop 1s

The quickest way to bypass FRP is to use a free Android apps launcher that allows access to settings during the setup wizard. After flashing or resetting, you may see a Google account lock (FRP). Our free Android apps launcher is the fastest method to get past it. Removing your Google account before flashing avoids this problem entirely.

---

Common Reasons to Reinstall Tecno Pop 1s Firmware

This device relies on a MediaTek chipset, so SP Flash Tool is the standard recovery method. Here is what flashing the stock firmware resolves:

• Repair a phone that shuts down randomly or restarts in a loop.
• Fix startup loops, lagging, and freezing on the device.
• Resolve OTA update failures and battery drain issues.
• Restore the original Tecno stock ROM to keep the warranty valid.
• Resolve touchscreen responsiveness issues caused by a corrupted system build.
• Update to the latest Android version supported by the phone.
• Recover from “Download DA FAIL” errors and Secure Boot authentication issues specific to the MediaTek chipset.

Learn more about stock ROMs and why flashing works.

---

How to Pick the Correct Tecno Pop 1s Firmware

Do not flash firmware meant for a different variant. Verify your exact device identity before downloading anything:

1. Open About Phone: Your device model must read “” exactly. Even small differences in the code can mean a completely different chipset and partition layout.
2. Verify the Chipset Type: This firmware targets MediaTek MT6739WA specifically. Flashing it on a different chipset will fail or could brick the device.
3. Check Your Current Firmware Version: Compare your build number with the versions listed in the download section to decide which file to use.
4. Use Recovery Mode: If you cannot access Settings (phone is stuck or locked), boot into recovery mode to read the build and chipset details from the screen.
5. Regional Compatibility: Some Tecno firmware packages target specific regions. Confirm the download matches your device origin.

---

Firmware Details for Tecno Pop 1s

Here is a quick overview of the official firmware specifications:

Firmware Information	Details
Device Model	Tecno Pop 1s
Firmware Version	V58
File Size	891.4 MB
Android Version	Android 8.1 Oreo (Go edition)
Platform	MediaTek MT6739WA
Release Date	Released 2018, July
Region	Global, Africa and Asia
File Type	ZIP (Includes Scatter File [MT6xxx_Android_scatter.txt], preloader.bin, boot.img, system.img, recovery.img, lk.bin, logo.bin, nvram.img, and more)

---

Which Firmware Version Should I Download?

Use the table below to identify the correct file for your specific situation:

Your Situation	What I Recommend
Phone is completely dead or stuck on logo	V58, download this one. It is the latest Tecno Pop 1s firmware available.
FRP / Google account lock only	See the FRP bypass guide above, you likely do not need the full firmware for this.
Phone slow after a recent OTA update	Try the next older version, sometimes the latest OTA introduces new bugs and an older build runs better.
IMEI missing after a previous flash	Re-flash V58 first, then follow the IMEI repair guide. Do not skip the reflash.
V58 failed with a flash error	Try the next older version instead and double-check your scatter file selection before assuming the firmware is the problem.
Restoring to factory / warranty repair	V58, clean state, fresh start.

My general approach with MTK devices: always try the latest version first. I have seen people spend a lot of time trying older builds when the newest one would have worked fine. Only move to an older version if the latest fails more than once, and make sure it is a driver issue you are solving, not a firmware issue.

---

Download Tecno Pop 1s Firmware

Download the official stock firmware for your Tecno Pop 1s below. The latest available version is V58. After downloading, verify the file size matches the table above, a size mismatch usually means a partial or corrupt download, and flashing a corrupt file can cause more problems than it solves.

Software Details	Download Link	Members Link
File Name: Tecno_Pop_1S_MT6739_V58_180620.zip Size: 891.4 MB	Download Link	Download Link2

Only download firmware that is fully compatible with your exact device model. See the firmware selection guide above if you are not sure.

---

Prerequisites for Tecno Pop 1s Firmware

Do not skip this section. Most failed Tecno flashes come from rushing through the preparation steps. The VCOM driver installation is essential for the Tecno Pop 1s and other MediaTek devices. Windows may show the device in Device Manager and SP Flash Tool will still not detect it if the correct VCOM driver is not installed.

1. Save Your IMEI Numbers: Type *#06# in the phone dialer and note down both numbers. These are your device identifiers for the cellular network. If flashing wipes them, you will need the originals to write them back.
2. Disconnect Google Accounts: Before you start anything, remove all Google accounts from the phone. Settings then Accounts then tap each Google account and remove it. This avoids the FRP verification screen that appears after flashing if accounts were still linked.
3. Create a Backup: Copy your data to your computer or an SD card. Flashing replaces the entire software on the phone, which means all personal data, apps, and settings will be permanently deleted.
4. Charge First: Get the battery above 50% before starting. The flashing process takes a few minutes and the first boot takes several more. A power failure during either stage can leave the device in a state that requires more advanced recovery.
5. Prepare Your PC Connection: You need a Windows computer and a USB cable that supports data transfer. Test the cable first by connecting the phone normally, if it shows up in File Explorer, the cable is good.
6. Install the Right Drivers:
   • VCOM Drivers
   • Tecno USB Drivers

---

Install Stock Firmware on Tecno Pop 1s

Use SP Flash Tool for Windows or SP Flash Tool for Linux. Load the scatter file from the extracted firmware folder, select “Download Only” (this preserves user data) or “Firmware Upgrade” (full wipe), and click the green Download button. SP Flash Tool will wait for the device, power it off completely, then connect the USB cable. If the latest SP Flash Tool does not detect this device, try SP Flash Tool v5.1924 instead, older MTK devices sometimes work better with older tool versions. The complete SP Flash Tool guide is also available if you need more detail.

1. Download the Firmware Package:
   • Use the download links in the table above to get the correct firmware file for your device.
   • Extract the archive with WinRAR or 7-Zip. Use a short folder path like D:flash to avoid issues with some tools.
2. Check Drivers:
   • All drivers from the prerequisites must be installed before connecting your device. Restart your computer after installing them.
3. Load the Firmware File:
   • Click on the “Scatter-loading” button. Navigate to the folder where you extracted the firmware and select the “scatter.txt” file.
4. Connect Your Device:
   • Power off your phone completely, not sleep mode, fully off.
   • Connect to your PC via USB cable. The flash tool will detect it automatically.
5. Start Flashing:
   • Press “Download” to begin writing the firmware to your device.
   • Do not unplug the phone, close the flash tool, or interact with the device until the process is 100% complete.
6. Wait and Reboot:
   • After the tool confirms the flash is complete, safely disconnect your phone.
   • Press the power button to start your device. The initial boot is slow, wait up to 8 minutes before assuming there is a problem.

---

Normal Behavior After Installing Tecno Pop 1s Firmware

Here is what is completely normal after a successful flash:

• How to know the flash was successful: SP Flash Tool will show a green circle or checkmark when done. If you see that, the flash completed successfully.
• Fingerprint and face unlock data are erased during the flash. You will need to re-register your fingerprints and face data from scratch in the security settings.
• Be careful when re-adding your Google account, if you did not remove it before flashing, you may see an FRP prompt. Add it fresh during the setup wizard, not afterwards through Settings.
• The phone will feel warm during first boot, this is normal. It settles after a few minutes once the initial app setup is complete.
• First boot takes 3 to 8 minutes, do not force-reboot the device. The operating system is setting itself up from scratch. Interrupting this is how devices end up in bootloops.
• Notification sounds and ringtones will be back to factory defaults. Any custom tones you had set before will need to be re-downloaded and re-assigned in Settings.
• The phone may ask for language and region again, this is normal after a flash. You are starting from a clean state, so the setup wizard runs just like when the phone was brand new.

---

Common Issues When Flashing Tecno Pop 1s

1. Tecno Pop 1s Not Recognized by SP Flash Tool:
   • In most cases this is a driver issue, not a cable issue. Reinstall the VCOM drivers for the , restart your PC, and try again before changing anything else.
   • If that does not work, switch to a USB 2.0 port, USB 3.0 ports can cause detection issues with MediaTek devices more often than people expect.
   • Still not working? Temporarily disable your antivirus. It can block the VCOM driver from loading without giving you any error message.
2. Boot Loop After Flashing:
   • Enter recovery mode and perform a factory reset from there. Most post-flash bootloops on MediaTek are caused by conflicts with old cached data, a wipe from recovery usually fixes this without needing to reflash.
3. Wrong Scatter File / Firmware Mismatch:
   • If SP Flash Tool throws an error as soon as you try to start the download, check your scatter file first. A mismatch between the scatter file and your device build is one of the most common causes of flash errors.
4. “Download DA FAIL” Error:
   • This error comes up regularly. It almost always means the VCOM driver is not properly installed. Reinstall it, restart your PC, and try again. If that still does not work, try switching to SP Flash Tool v5.1924, older devices sometimes respond better to the older version.
5. Error 8038 (BROM Error):
   • The device is not entering BROM mode correctly. Power it off completely and, if possible, remove the battery for 30 seconds. Reconnect and try again. Some MediaTek devices require you to hold Volume Down while plugging in the USB cable to enter BROM mode.
6. Auth File / Secure Boot Error in Newer SP Flash Tool:
   • Newer versions of SP Flash Tool require a DA (Download Agent) authentication file for devices with Secure Boot enabled. If you do not have that file, switch to MTK Client instead, it handles Secure Boot automatically and is the simpler solution.

---

Missing IMEI or Corrupt Baseband on Tecno Pop 1s After Flashing?

A missing or unknown IMEI is one of the most common things I see after a MediaTek flash. It happens because the NVRAM partition, which stores your IMEI and calibration data, sometimes does not survive the flash intact. It looks alarming, but it is fixable. Here is what to do:

1. Check your drivers first: Install the Mediatek CDC Driver if you have not already, without it, the IMEI repair tools will not detect your device. This is the step most people miss.
2. Use SN Write Tool or Maui Meta: SN Write Tool is the first option I try, it is straightforward and works on most MTK devices. Maui Meta is the alternative if SN Write does not connect. You can learn more about using SN Write Tool here.
3. Run the repair:
   • Connect your device to the computer.
   • Enter the original IMEI numbers for both SIM slots, these are the numbers you wrote down before flashing.
   • Click “Start” and let it complete without interrupting the connection.
4. Verify after reboot: Once done, reboot your phone and dial *#06#. Your IMEI numbers should be back. If they are still showing null, run the process again, sometimes the first attempt does not complete correctly.

Video Guide: How to repair IMEI

Credits: https://www.youtube.com/@mhgsmclinic

---

Tecno Pop 1s Flashing FAQ

Q1: What if the flash fails halfway through?
A: Do not panic and do not disconnect the phone. Close SP Flash Tool, restart it, and try the flash again from the beginning. In most cases, a failed flash just means the process needs to be repeated. The device is usually still detectable by the flash tool even after a failed attempt.

Q2: Is this firmware compatible with other Tecno models?
A: No. This firmware is built specifically for the Tecno Pop 1s running on the MediaTek MT6739WA chipset. Even variants of the Pop 1s with a different letter suffix can have a completely different chipset inside. Flashing the wrong firmware can leave your phone in a state that is very difficult to recover from. Always check your exact model number in Settings.

Q3: Is it safe to flash during a power outage risk?
A: It is best to avoid flashing during unstable power conditions. If your PC shuts down during the flash, it can corrupt the write and leave the phone in an unbootable state. If you are in an area with unreliable power, use a laptop with a fully charged battery instead of a desktop.

Q4: What should I do if I encounter an FRP lock after flashing?
A: Use our free Android apps launcher. FRP lock activates when a Google account was still signed in before flashing. This is why signing out of your Google account before flashing avoids this issue entirely.

Q5: Can I use a Mac or Linux computer for this?
A: The tools and drivers referenced on this page are Windows-only. If you are on Mac or Linux, your best option is to use a Windows virtual machine, or borrow a Windows PC for the 10 minutes it takes to complete the flash.

Q6: Can I go back to an older firmware version?
A: Downgrading is possible on most MediaTek devices, but not always safe. Some OEMs have started implementing anti-rollback on newer models, if the flash tool throws an error during a downgrade attempt, stop. Flashing the same or a newer version is always the safer option.

Q7: How long does the flashing process take?
A: The actual flash usually takes between 3 and 10 minutes depending on the firmware size and USB connection speed. The first boot after flashing takes another 3 to 8 minutes. Do not interrupt the device during either stage. If the progress bar in SP Flash Tool appears stuck, give it a few more minutes before assuming something went wrong.

Q8: My IMEI shows “unknown” after flashing. Is my phone permanently damaged?
A: No, it looks alarming, but it is fixable. Follow the IMEI repair guide in the troubleshooting section above. For MediaTek devices, SN Write Tool or Maui Meta will handle the repair. Do not insert a SIM card until the IMEI is restored.

---

Final Thoughts

The flash is done. Your Tecno Pop 1s is back on official stock firmware and should be running without the issues that brought you here.

If anything went differently than described, an error message, a step that did not match your setup, post it in the comments. I respond to every question.

This guide gets updated when new builds are released, so you can come back anytime you need a newer version.

Browse all Tecno firmware downloads for more devices.

---

Disclaimer: Flashing stock firmware is performed at your own risk. Follow the instructions on this page carefully. I cannot be held responsible for any damage to your device, but I will always try to help if something goes wrong.