Last Updated: May 5, 2026
You can restore your Tecno Camon CX Manchester City LE to factory settings using this official firmware. I have gathered the necessary files and the steps to fix common software problems.
Device: Tecno Camon CX Manchester City LE | Chipset: Mediatek MT6750T (28 nm) | Flash Tool: SP Flash Tool
Android: Android 7.0 (Nougat) | File Type: ZIP (Includes Scatter File [MT6xxx_Android_scatter.txt], preloader.bin, boot.img, system.img, recovery.img, lk.bin, logo.bin, nvram.img, and more)
⚠ Warning: Flashing erases all data. Back up first.
Tecno Camon CX Manchester City LE Firmware (Flash File) Drivers, Tools & Guide
I have repaired many Tecno phones, and the Camon CX Manchester City LE is a common repair. It usually comes in with FRP locks, bootloops, or stuck on the logo. I put the firmware, tools, and steps together in one place.
Before you start, extract the firmware to a simple folder path like C:FirmwareLE. SP Flash Tool can have trouble finding the scatter file if the path has spaces or special characters. It is a small detail, but it saves time.
Download and extract the firmware using WinRAR or 7-Zip. Once extracted, check the folder to make sure the scatter file is there before you proceed.
Keep in mind that flashing stock firmware erases all data. This is intentional. It resolves software issues including FRP lock, app problems, slow performance, forgotten pattern locks, a dead or logo-stuck device, Wi-Fi and Bluetooth issues, battery drain, and soft brick situations.
Tecno Camon CX Manchester City LE FRP Bypass
You might see a Google account lock (FRP) after flashing or performing a factory reset. The fastest way to bypass this is using our free Android apps launcher. This is also why I always recommend removing your Google account before you flash it avoids this problem entirely.
Why Do We Need Tecno Camon CX Manchester City LE Firmware?
This device runs on a MediaTek chipset, and SP Flash Tool is the standard way to recover it. Here is what flashing the stock firmware can help with:
- Unlock your device if it has been locked or disabled.
- Update to the latest Android version supported by your phone.
- Fix startup loops, lagging, and freezing on your LE Camon CX Manchester City LE.
- Resolve OTA update failures and battery drain issues.
- Restore the original Tecno stock ROM to keep your warranty valid.
- Recover your device when it only boots into recovery mode.
- Recover from “Download DA FAIL” errors and Secure Boot authentication issues specific to the MediaTek chipset in your device.
Learn more about stock ROMs and why flashing works.
Choosing the Right Firmware Version
Before you begin flashing, double-check you have the right file. Flashing the wrong firmware is difficult to recover from:
- Identify Your Device Model: Go to About Phone and confirm your model is Tecno Camon CX Manchester City LE. Check the full model string, not just the name.
- Verify the Build Number: Look for the identifier “LE” in your device build details.
- Confirm the Chipset: According to Tecno specifications, the Camon CX Manchester City LE LE runs on Mediatek MT6750T (28 nm).
- Match the Firmware Version: Check the version and regional details against what is listed in the download table above.
- Verify in Recovery Mode: If you are not sure about the chipset or build number, boot into recovery mode it displays this information clearly and is the most reliable way to confirm before you flash.
Firmware Details for Tecno Camon CX Manchester City LE
Here is a quick overview of the official firmware specifications:
| Firmware Information | Details |
|---|---|
| Device Model | Tecno Camon CX Manchester City LE |
| Firmware Version | N/A |
| File Size | N/A |
| Android Version | Android 7.0 (Nougat) |
| Platform | Mediatek MT6750T (28 nm) |
| Release Date | Released 2017, March |
| Region | Global, Africa and Asia |
| File Type | ZIP (Includes Scatter File [MT6xxx_Android_scatter.txt], preloader.bin, boot.img, system.img, recovery.img, lk.bin, logo.bin, nvram.img, and more) |
Which Firmware Version Should I Download?
People often ask which version to download. Here is a simple guide to help you choose:
| Your Situation | What I Recommend |
|---|---|
| Phone is completely dead or stuck on logo | the latest version download this one. It is the latest Tecno Camon CX Manchester City LE firmware available. |
| FRP / Google account lock only | See the FRP bypass guide above you likely do not need the full firmware for this. |
| Phone slow after a recent OTA update | Try the next older version sometimes the latest OTA introduces new bugs and an older build runs better. |
| IMEI missing after a previous flash | Re-flash the latest version first, then follow the IMEI repair guide. Do not skip the reflash. |
| the latest version failed with a flash error | Try the next older version instead and double-check your scatter file selection before assuming the firmware is the problem. |
| Restoring to factory / warranty repair | the latest version clean state, fresh start. |
My general approach with MTK devices: always try the latest version first. I have seen people spend a lot of time trying older builds when the newest one would have worked fine. Only move to an older version if the latest fails more than once, and make sure it is a driver issue you are solving, not a firmware issue.
Download Tecno Camon CX Manchester City LE Firmware
Download the official stock firmware for your Tecno Camon CX Manchester City LE below. The latest available version is the latest version. After downloading, verify the file size matches the table above a size mismatch usually means a partial or corrupt download, and flashing a corrupt file can cause more problems than it solves.
Only download firmware that is fully compatible with your exact device model. See the firmware selection guide above if you are not sure.
- Your model number is a variant of LE with a different letter suffix. Check About Phone carefully one letter difference can cause a failed or broken flash.
- Your chipset differs from Mediatek MT6750T (28 nm). Confirm in recovery mode before proceeding.
- You downloaded the file from a source other than this page.
- The file size differs significantly from the sizes listed in the table above a size mismatch usually means a partial download, which will fail mid-flash.
Prerequisites
Do not skip this section. Most failed flashes happen because of rushed preparation. The VCOM driver is essential for MediaTek devices. Windows might show the device in Device Manager, but SP Flash Tool will not detect it if the correct VCOM driver is not installed.
- Back Up IMEI Numbers: Dial *#06# and write down both IMEI numbers now. You will need these if you need to restore your IMEI after flashing.
- Remove Google Accounts: Sign out of all Google accounts to prevent FRP lock after flashing.
- Back Up Your Data: Back up everything photos, contacts, WhatsApp chats, important files. Flashing wipes the device completely.
- Charge Your Device: At least 50% battery. A device that powers off during a flash is very difficult to recover.
- USB Cable & PC: Use a proper data USB cable not a charge-only cable and a Windows computer with available USB ports.
- Install Required Drivers:
How to Install Firmware on Tecno Camon CX Manchester City LE
We are using SP Flash Tool for this. For older devices, I recommend trying SP Flash Tool v5.1924 first. The newer versions of SP Flash Tool require a DA (Download Agent) file that older firmware packages do not include, and that is what causes the “Auth” errors you may have seen. If SP Flash Tool keeps asking for an auth file and you do not have one, switch to MTK Client it handles Secure Boot automatically. Download SP Flash Tool for Windows or SP Flash Tool for Linux and follow the steps below. The complete SP Flash Tool guide is also available if you need more detail.
- Download and Extract:
- Download the correct firmware package from the links above.
- Extract the ZIP to a simple folder path avoid paths with spaces or special characters, as some flash tools have trouble with them.
- Install the Listed Drivers:
- Confirm all drivers listed above are installed and that your PC has been restarted since installation. Skipping the restart is a common reason drivers do not work correctly.
- Load the Firmware File:
- Click on the “Scatter-loading” button. Navigate to the folder where you extracted the firmware and select the “scatter.txt” file.
- Connect Your Device:
- Power off your phone completely not sleep mode, fully off.
- Connect to your PC via USB cable. The flash tool will detect it automatically.
- Start Flashing:
- Click the “Download” button to begin.
- Do not disconnect, move the cable, or touch the device until the process is fully complete. Disconnecting mid-flash is how devices get bricked.
- Wait and Reboot:
- Once flashing finishes successfully, disconnect the device.
- Power on your device. The first boot will take longer than usual give it up to 8 minutes.
What to Expect After Flashing Your Tecno Camon CX Manchester City LE
I get a lot of comments from people who think something went wrong when it actually did not. Here is what is completely normal after a successful flash:
- How to know the flash was successful: SP Flash Tool will show a green circle or checkmark when done. If you see that, the flash completed successfully.
- First boot takes 3 to 8 minutes do not force-reboot the device. The operating system is setting itself up from scratch. Interrupting this is how devices end up in bootloops.
- The phone will feel warm during first boot this is normal. It settles after a few minutes once the initial app setup is complete.
- All your apps are gone this is expected. Reinstall them from the Play Store. If you had a Google account backup active, it will offer to restore your apps automatically during setup.
- Dial *#06# immediately after setup to check your IMEI. Do this before you insert a SIM card. If it shows “unknown” or “null”, follow the IMEI repair guide below before doing anything else.
- Be careful when re-adding your Google account if you did not remove it before flashing, you may see an FRP prompt. Add it fresh during the setup wizard, not afterwards through Settings.
- Wi-Fi, Bluetooth, and mobile data should all work right after setup. If mobile data is not connecting, go to Settings › SIM and Network and re-enter your APN manually the flash sometimes clears carrier APN settings.
- Stuck in a bootloop after first boot? Enter recovery mode and do a factory reset from there. This can happen occasionally and does not mean the firmware is wrong it is usually a conflict with leftover data from the old install.
Missing IMEI or Corrupt Baseband After Flashing?
A missing or unknown IMEI is one of the most common things I see after a MediaTek flash. It happens because the NVRAM partition, which stores your IMEI and calibration data, sometimes does not survive the flash intact. It looks alarming, but it is fixable. Here is what to do:
- Check your drivers first: Install the Mediatek CDC Driver if you have not already without it, the IMEI repair tools will not detect your device. This is the step most people miss.
- Use SN Write Tool or Maui Meta: SN Write Tool is the first option I try it is straightforward and works on most MTK devices. Maui Meta is the alternative if SN Write does not connect. You can learn more about using SN Write Tool here.
- Run the repair:
- Connect your device to the computer.
- Enter the original IMEI numbers for both SIM slots these are the numbers you wrote down before flashing.
- Click “Start” and let it complete without interrupting the connection.
- Verify after reboot: Once done, reboot your phone and dial *#06#. Your IMEI numbers should be back. If they are still showing null, run the process again sometimes the first attempt does not complete correctly.
Video Guide: How to repair IMEI
Credits: https://www.youtube.com/@mhgsmclinic
Common Issues and Solutions
- Device Not Recognized by SP Flash Tool:
- In most cases this is a driver issue, not a cable issue. Reinstall the VCOM drivers, restart your PC, and try again before changing anything else.
- If that does not work, switch to a USB 2.0 port USB 3.0 ports can cause detection issues with MediaTek devices more often than people expect.
- Still not working? Temporarily disable your antivirus. It can block the VCOM driver from loading without giving you any error message.
- Boot Loop After Flashing:
- Enter recovery mode and perform a factory reset from there. Most post-flash bootloops on MediaTek are caused by conflicts with old cached data a wipe from recovery usually fixes this without needing to reflash.
- Wrong Scatter File / Firmware Mismatch:
- If SP Flash Tool throws an error as soon as you try to start the download, check your scatter file first. A mismatch between the scatter file and your device build is one of the most common causes of flash errors.
- “Download DA FAIL” Error:
- This error comes up regularly. It almost always means the VCOM driver is not properly installed. Reinstall it, restart your PC, and try again. If that still does not work, try switching to SP Flash Tool v5.1924 older devices sometimes respond better to the older version.
- Error 8038 (BROM Error):
- The device is not entering BROM mode correctly. Power it off completely and, if possible, remove the battery for 30 seconds. Reconnect and try again. Some MediaTek devices require you to hold Volume Down while plugging in the USB cable to enter BROM mode.
- Auth File / Secure Boot Error in Newer SP Flash Tool:
- Newer versions of SP Flash Tool require a DA (Download Agent) authentication file for devices with Secure Boot enabled. If you do not have that file, switch to MTK Client instead it handles Secure Boot automatically and is the simpler solution.
Frequently Asked Questions
Q1: Will flashing the Tecno Camon CX Manchester City LE firmware erase my data?
A: Yes flashing restores your device to factory state. All apps, photos, contacts, and accounts will be removed. Back up everything you need before you start. There is no way to recover data once the flash is complete.
Q2: Is this firmware compatible with other Tecno models?
A: No. This firmware is built specifically for the Tecno Camon CX Manchester City LE. Even devices with very similar names can have different chipset variants. Flashing the wrong firmware can leave your phone in a state that is very difficult to recover from.
Q3: Can I downgrade my firmware version?
A: It is technically possible on some builds, but I do not recommend it. Downgrading can cause security issues and app compatibility problems. If a newer firmware build is causing you trouble, leave a comment below there is usually a better fix than rolling back.
Q4: What should I do if I encounter an FRP lock after flashing?
A: Use our free Android apps launcher. This is also why I always recommend signing out of your Google account before flashing it avoids this issue entirely.
Q5: Are custom ROM options available for the Tecno Camon CX Manchester City LE?
A: This guide covers official stock firmware only. For custom ROMs, check our Custom ROMs page or the XDA Developers forum.
Q6: My Tecno Camon CX Manchester City LE is not detected by the flash tool. What should I do?
A: Start with the drivers reinstall them, restart your PC, then try again. Switch to a USB 2.0 port if you are on USB 3.0. Disable your antivirus temporarily. If none of that works, leave a comment below with the exact error message you are seeing and I will help you from there.
Q7: How do I enter recovery mode on my Tecno Camon CX Manchester City LE?
A: Power the device off completely, then hold Volume Up + Power at the same time until the recovery menu appears. The exact button combination can vary slightly between Tecno models if this does not work, let me know your exact model in the comments.
Q8: My IMEI shows “unknown” after flashing. Is my phone permanently damaged?
A: No it looks alarming, but it is fixable. Follow the IMEI repair guide in the troubleshooting section above. The important thing: do not insert a SIM card until the IMEI is restored. And for next time, always write down your IMEI by dialing *#06# before you flash you will need the original number to restore it.
Q9: Can I flash this firmware on a Mac or Linux computer?
A: SP Flash Tool has a Linux build linked on this page, so Linux users are covered. Mac is not officially supported by any of the major flash tools. If you are on a Mac, using a Windows computer for the flash is the easiest option.
Conclusion
You now have the files and steps to flash the official Tecno Camon CX Manchester City LE firmware (the latest version) using SP Flash Tool and get your device working again. If you followed each step, your phone should now be running on a clean build.
If something did not go as expected a specific error, a step that is not working for your setup leave a comment below with as much detail as you can: the exact error message, which step you are on, and what you have already tried. I read every comment and will help you work through it.
If this guide helped you, consider sharing it it is the best way to help someone else who is dealing with the same problem.
Disclaimer: Flashing stock firmware is performed at your own risk. Follow the instructions on this page carefully. I cannot be held responsible for any damage to your device, but I will always try to help if something goes wrong.
