Infinix Xpad X1101 Firmware

Last Updated: August 9, 2026

If your Infinix Xpad X1101 is stuck or acting up, the official firmware below can help fix it. I have put together the files and steps you need to get it running smoothly again.

---

Infinix Xpad X1101 Firmware (Flash File) Drivers, Tools & Guide

This guide provides the stock firmware, drivers, and step-by-step instructions needed to fix software issues on your Infinix Xpad X1101.

I have fixed many Infinix devices over the years, and the Xpad X1101 is a common visitor. It usually arrives with bootloops or an FRP lock. I have gathered the necessary tools and files here. Before starting, extract the firmware to a folder like C:FirmwareX1101. SP Flash Tool works better when the path is simple without spaces. This phone runs Android 14 and XOS 14, which defines the interface and apps you see after the update. This firmware was released in 2024 and targets the Global, Africa, and Asia regions. Infinix shares similar hardware with other Transsion brands, so the flashing process is consistent across the lineup.

Download the ZIP file using WinRAR or 7-Zip. Make sure to extract it first. Flashing replaces your current software completely and wipes all personal data. This is by design, it is what clears out FRP locks, bootloops, pattern locks, app crashes, and other software-level problems that a regular reset cannot fix.

---

Infinix Xpad X1101 Hard Reset Guide

To factory reset your Infinix Xpad X1101 without a computer, power it off completely, then hold Volume Up and Power together until the recovery menu appears.

A hard reset erases all data and restores Infinix Xpad X1101 to its original factory state. This fixes most software problems, slow performance, app crashes, forgotten screen locks, and bootloops. If the issue persists after a factory reset, a full firmware flash using SP Flash Tool is required.

---

Bypass Google Lock on Infinix Xpad X1101

The fastest way to bypass the Google lock on Infinix Xpad X1101 is to use an Android apps launcher during the setup wizard.

---

Common Reasons to Reinstall Infinix Xpad X1101 Firmware

You should reinstall the stock firmware on your Infinix Xpad X1101 if you are experiencing bootloops, lagging, or connectivity issues.

• Fix startup loops, lagging, and freezing on your device.
• Resolve OTA update failures and battery drain issues.
• Repair a phone that shuts down randomly or restarts in a loop.
• Unlock your device if it has been locked or disabled.
• Fix Wi-Fi, Bluetooth, or mobile data connectivity that stopped working after an update.
• Resolve touchscreen responsiveness issues caused by a corrupted system build.
• Recover from “Download DA FAIL” errors and Secure Boot authentication issues specific to the MediaTek chipset in your device.

Learn more about stock ROMs and why flashing works.

---

Which Firmware Version Does Your Infinix Xpad X1101 Need?

You must verify your exact device model before downloading firmware for your Infinix Xpad X1101 to avoid flashing the wrong file.

1. Check About Phone: Open Settings and find your exact model number. It should read “X1101”, not a similar name, the exact code.
2. Match the Chipset: This firmware is built for MediaTek Helio G99. If your device has a different processor, it will not flash correctly.
3. Look at the Build Number: The build string in your current software should reference the Xpad line. Cross-check it with the firmware table below.
4. Check Recovery Mode: Power off, hold Volume Up + Power until recovery appears. The screen displays your chipset and current build, use this to confirm.
5. Compare File Details: Make sure the version listed in the download table matches what you expect for your device and region.

---

Firmware Details for Infinix Xpad X1101

Here is a quick overview of the official firmware specifications:

Firmware Information	Details
Device Model	Infinix Xpad X1101
Firmware Version	V682
File Size	4.3 GB
Android Version	Android 14, XOS 14
Platform	MediaTek Helio G99
Release Date	Released 2024, August 18
Region	Global, Africa and Asia
File Type	ZIP (Includes Scatter File [MT6xxx_Android_scatter.txt], preloader.bin, boot.img, system.img, recovery.img, lk.bin, logo.bin, nvram.img, and more)

---

Which Firmware Version Should I Download?

Use the table below to determine which specific firmware file you need for your Infinix Xpad X1101 situation.

Your Situation	What I Recommend
Phone is completely dead or stuck on logo	V682, download this one. It is the latest Infinix Xpad X1101 firmware available.
FRP / Google account lock only	See the FRP bypass guide above, you likely do not need the full firmware for this.
Phone slow after a recent OTA update	Try the next older version, sometimes the latest OTA introduces new bugs and an older build runs better.
IMEI missing after a previous flash	Re-flash V682 first, then follow the IMEI repair guide. Do not skip the reflash.
V682 failed with a flash error	Try the next older version instead and double-check your scatter file selection before assuming the firmware is the problem.
Restoring to factory / warranty repair	V682, clean state, fresh start.

My general approach with MTK devices: always try the latest version first. I have seen people spend a lot of time trying older builds when the newest one would have worked fine. Only move to an older version if the latest fails more than once, and make sure it is a driver issue you are solving, not a firmware issue.

---

Download Infinix Xpad X1101 Firmware

Download the official stock firmware for your Infinix Xpad X1101 below. The latest available version is V682. After downloading, verify the file size matches the table above, a size mismatch usually means a partial or corrupt download, and flashing a corrupt file can cause more problems than it solves.

Software Details	Download Link	Members Link
File Name: Infinix_XPad_X1101_MT6789_OP_V682_240626_MXML.zip Size: 4.3 GB	Download Link	Download Link2

Only download firmware that is fully compatible with your exact device model. See the firmware selection guide above if you are not sure.

Important: The Infinix Xpad X1101 (X1101) should not be confused with other Xpad variants that may have different chipsets or regional firmware. Even devices in the same Xpad line can use completely different processors. Always verify your exact model code “X1101” in Settings > About Phone before downloading any firmware from this page.

---

Prerequisites for Infinix Xpad X1101 Firmware

You need to prepare your computer and device correctly before attempting to flash the Infinix Xpad X1101 firmware.

1. Save Your IMEI Numbers: Type *#06# in the phone dialer and note down both numbers. These are your device identifiers for the cellular network. If flashing wipes them, you will need the originals to write them back.
2. Disconnect Google Accounts: Before you start, remove all Google accounts from the phone. Settings then Accounts then tap each Google account and remove it. This avoids the FRP verification screen that appears after flashing if accounts were still linked.
3. Create a Backup: Copy your data to your computer or an SD card. Flashing replaces the entire software on the phone, which means all personal data, apps, and settings will be permanently deleted.
4. Charge First: Get the battery above 50% before starting. The flashing process takes a few minutes and the first boot takes several more. A power failure during either stage can leave the device in a state that requires more advanced recovery.
5. Prepare Your PC Connection: You need a Windows computer and a USB cable that supports data transfer. Test the cable first by connecting the phone normally, if it shows up in File Explorer, the cable is good.
6. Install the Right Drivers:
   • VCOM Drivers
   • Infinix USB Drivers

---

Step-by-Step: Flash Infinix Xpad X1101 Stock ROM

Follow these steps to flash the stock ROM onto your Infinix Xpad X1101 using SP Flash Tool.

1. Get the Firmware Ready:
   • Download the firmware file from the download section above.
   • Right-click the ZIP and select “Extract Here” or use 7-Zip. Put the extracted files in a folder without spaces in the name, like C:firmware.
2. Verify Your Drivers:
   • Make sure the required drivers are installed. After installing, restart your PC, drivers often do not activate until after a reboot.
3. Load the Firmware File:
   • Click on the “Scatter-loading” button. Navigate to the folder where you extracted the firmware and select the “scatter.txt” file.
4. Connect Your Device:
   • Power off your phone completely, not sleep mode, fully off.
   • Connect to your PC via USB cable. The flash tool will detect it automatically.
5. Start Flashing:
   • Hit the “Download” button in the flash tool to start the process.
   • Leave the phone and cable completely alone until it finishes. Any interruption during this stage risks corrupting the flash.
6. Wait and Reboot:
   • When the flash completes, unplug the USB cable from your phone.
   • Turn on the device. First boot takes 3 to 8 minutes, do not force restart it during this time.

---

What Is Normal After a Infinix Xpad X1101 Flash?

You will notice several changes after a successful flash, including storage capacity changes and the need to re-register biometrics.

• How to know the flash was successful: SP Flash Tool will show a green circle or checkmark when done. If you see that, the flash completed successfully.
• Storage will show almost full capacity available since all your apps and files are gone. The system partition size varies by firmware version but is typically 4 to 8 GB on most devices.
• Battery percentage may seem inaccurate for the first day. The battery statistics are calibrated during normal use. Charge the phone fully once without interruption and the readings will stabilize.
• Notification sounds and ringtones will be back to factory defaults. Any custom tones you had set before will need to be re-downloaded and re-assigned in Settings.
• The phone will feel warm during first boot, this is normal. It settles after a few minutes once the initial app setup is complete.
• Fingerprint and face unlock data are erased during the flash. You will need to re-register your fingerprints and face data from scratch in the security settings.
• First boot takes 3 to 8 minutes, do not force-reboot the device. The operating system is setting itself up from scratch. Interrupting this is how devices end up in bootloops.

---

Troubleshooting Infinix Xpad X1101 Flash Errors

1. Infinix Xpad X1101 Not Recognized by SP Flash Tool:
   • In most cases this is a driver issue, not a cable issue. Reinstall the VCOM drivers for the X1101, restart your PC, and try again before changing anything else.
   • If that does not work, switch to a USB 2.0 port, USB 3.0 ports can cause detection issues with MediaTek devices more often than people expect.
   • Still not working? Temporarily disable your antivirus. It can block the VCOM driver from loading without giving you any error message.
2. Boot Loop After Flashing:
   • Enter recovery mode and perform a factory reset from there. Most post-flash bootloops on MediaTek are caused by conflicts with old cached data, a wipe from recovery usually fixes this without needing to reflash.
3. Wrong Scatter File / Firmware Mismatch:
   • If SP Flash Tool throws an error as soon as you try to start the download, check your scatter file first. A mismatch between the scatter file and your device build is one of the most common causes of flash errors.
4. “Download DA FAIL” Error:
   • This error comes up regularly. It almost always means the VCOM driver is not properly installed. Reinstall it, restart your PC, and try again. If that still does not work, try switching to SP Flash Tool v5.1924, older devices sometimes respond better to the older version.
5. Error 8038 (BROM Error):
   • The device is not entering BROM mode correctly. Power it off completely and, if possible, remove the battery for 30 seconds. Reconnect and try again. Some MediaTek devices require you to hold Volume Down while plugging in the USB cable to enter BROM mode.
6. Auth File / Secure Boot Error in Newer SP Flash Tool:
   • Newer versions of SP Flash Tool require a DA (Download Agent) authentication file for devices with Secure Boot enabled. If you do not have that file, switch to MTK Client instead, it handles Secure Boot automatically and is the simpler solution.

---

Missing IMEI or Corrupt Baseband on Infinix Xpad X1101 After Flashing?

A missing or unknown IMEI is one of the most common things I see after a MediaTek flash. It happens because the NVRAM partition, which stores your IMEI and calibration data, sometimes does not survive the flash intact. It looks alarming, but it is fixable. Here is what to do:

1. Check your drivers first: Install the Mediatek CDC Driver if you have not already, without it, the IMEI repair tools will not detect your device. This is the step most people miss.
2. Use SN Write Tool or Maui Meta: SN Write Tool is the first option I try, it is straightforward and works on most MTK devices. Maui Meta is the alternative if SN Write does not connect. You can learn more about using SN Write Tool here.
3. Run the repair:
   • Connect your device to the computer.
   • Enter the original IMEI numbers for both SIM slots, these are the numbers you wrote down before flashing.
   • Click “Start” and let it complete without interrupting the connection.
4. Verify after reboot: Once done, reboot your phone and dial *#06#. Your IMEI numbers should be back. If they are still showing null, run the process again, sometimes the first attempt does not complete correctly.

Video Guide: How to repair IMEI

Credits: https://www.youtube.com/@mhgsmclinic

---

Common Questions About Flashing Infinix Xpad X1101

Q1: What should I do if I encounter an FRP lock after flashing?
A: Use our free Android apps launcher. FRP lock activates when a Google account was still signed in before flashing. This is why signing out of your Google account before flashing avoids this issue entirely.

Q2: My IMEI shows “unknown” after flashing. Is my phone permanently damaged?
A: No, it looks alarming, but it is fixable. Follow the IMEI repair guide in the troubleshooting section above. For MediaTek devices, SN Write Tool or Maui Meta will handle the repair. Do not insert a SIM card until the IMEI is restored.

Q3: Can I flash this firmware if my phone does not turn on at all?
A: Yes, in most cases. As long as the phone responds to a USB connection (even with a black screen), the flash tool can detect it. If the battery is completely drained, charge it for at least 15 minutes first.

Q4: Do I need an internet connection during flashing?
A: No. The flashing process is entirely offline, it happens between your PC and the phone via the USB cable. You do not need internet at any point during the flash itself. You will need internet later to set up the phone and download your apps.

Q5: Will flashing void my warranty?
A: Flashing official stock firmware generally does not void your warranty since you are restoring the device to its factory-intended state. However, some manufacturers may flag that the bootloader was unlocked or that the flash counter increased. Check your specific warranty terms with Infinix support if you are concerned.

Q6: How do I enter recovery mode?
A: Power the device off completely, then hold Volume Up + Power at the same time until the recovery menu appears. The recovery menu displays the build number which you can use to verify your firmware version before flashing.

Q7: My device is not detected by SP Flash Tool. What should I do?
A: Start with the drivers, reinstall the VCOM drivers, restart your PC, then try again. Switch to a USB 2.0 port if you are on USB 3.0. Disable your antivirus temporarily. If none of that works, leave a comment with the exact error message.

Q8: Can I use a Mac or Linux computer for this?
A: The tools and drivers referenced on this page are Windows-only. If you are on Mac or Linux, your best option is to use a Windows virtual machine, or borrow a Windows PC for the 10 minutes it takes to complete the flash.

People Also Ask About Infinix Xpad X1101

Can flashing firmware fix a bricked Infinix Xpad X1101?
Yes. If your Infinix Xpad X1101 is stuck on the logo, in a bootloop, or will not turn on, flashing the stock firmware with SP Flash Tool can restore it to working condition. This is the standard repair method used by service centers for Infinix devices.

How do I check my Infinix Xpad X1101 model number before flashing?
Go to Settings > About Phone on your Infinix Xpad X1101 and look for the model number “X1101”. You can also confirm by entering recovery mode (Volume Up + Power while powered off) which displays the build number and model code. Always match this exactly with the firmware filename before flashing.

What is the latest firmware version for Infinix Xpad X1101?
The latest available Infinix Xpad X1101 firmware on this page is version V682. This page has 1 firmware build available for download. Check the firmware details table above for file sizes and Android versions.

What chipset does the Infinix Xpad X1101 use?
The Infinix Xpad X1101 uses the MediaTek Helio G99 chipset, a MediaTek processor. This means you need SP Flash Tool and VCOM/MTK USB drivers to flash firmware. MediaTek devices use scatter-file-based flashing, which is different from Qualcomm (QFIL) or Samsung (Odin) methods.

---

Infinix Xpad X1101 Firmware, Final Notes

You now have everything needed to flash your Infinix Xpad X1101 back to stock using SP Flash Tool. The process is straightforward as long as you follow the steps in order and do not skip the driver installation.

Got stuck somewhere? Drop a comment with the error message and the step number. I check comments regularly and will point you in the right direction.

If this worked for you, share the page so others with the same device can find it too.

Browse all Infinix firmware downloads for more devices.

---

Disclaimer: Flashing stock firmware is performed at your own risk. Follow the instructions on this page carefully. I cannot be held responsible for any damage to your device, but I will always try to help if something goes wrong.