Infinix Note Edge X6887 Firmware

Last Updated: August 20, 2026

This guide provides the Infinix Note Edge X6887 firmware files, necessary drivers, and step-by-step instructions to unbrick, bypass FRP, or perform a clean reflash. ⚡ At a Glance Device: Infinix Note Edge X6887  |  Chipset: MediaTek Dimensity 7100 (MT6858)  |  Flash Tool: SP Flash Tool Android: Android 16, XOS 16  |  File Type: ZIP (Includes Scatter File [MT6xxx_Android_scatter.txt], preloader.bin, boot.img, system.img, recovery.img, lk.bin, logo.bin, nvram.img, and more) ⚠ Warning: Flashing erases all data. Back up first.

---

Infinix Note Edge X6887 Firmware (Flash File) Drivers, Tools & Guide

I have handled many Infinix repairs over the years, and the Infinix Note Edge X6887 is a frequent visitor in the workshop. It usually arrives with bootloops, a stuck logo, or FRP lock issues. This guide puts everything you need into one place: the files, the tools, and the process I use in the workshop.

Before you start, extract the firmware to a simple folder path, such as C:FirmwareX6887. SP Flash Tool often struggles to locate the scatter file if the path contains spaces or special characters. This simple step saves a lot of troubleshooting time.

There is currently only one firmware build available for the Infinix Note Edge X6887. This is the stock Infinix Note Edge X6887 firmware you need for recovery, unbricking, or bypassing FRP. The device runs on a MediaTek Dimensity 7100 (MT6858) chipset, which means you must use SP Flash Tool and MTK drivers. The firmware ships with Android 16 and XOS 16, which sets the default apps and interface you will see after the flash.

This firmware comes from verified sources and has been checked for integrity before being listed here. As a Transsion Holdings brand, Infinix devices share similar flashing procedures and architecture across the Note Edge series.

The firmware package is a compressed ZIP file. Download and extract it using WinRAR or 7-Zip. Once extracted, open the folder and verify it contains the scatter file before proceeding.

This process wipes the phone to its original factory state, so all your personal data will be gone. This clean slate fixes persistent problems like bootloops, forgotten locks, battery drain, and system errors.

---

Factory Reset Infinix Note Edge X6887 Without a PC

To perform a hard reset without a computer, power off the device completely. Then hold Volume Up and Power at the same time until the recovery menu appears. Use the volume keys to navigate to “Wipe Data/Factory Reset” and confirm with the Power button.

A hard reset wipes all data and restores the Infinix Note Edge X6887 to its original factory state. This resolves most software issues such as slow performance, app crashes, forgotten screen locks, and bootloops. If the problem persists after a factory reset, a full firmware flash is required.

---

FRP Removal for Infinix Note Edge X6887

The quickest way to bypass FRP on this device is to use a free Android apps launcher that allows access to settings during the setup wizard. After flashing or resetting, you might see a Google account lock. Our free Android apps launcher is the fastest method to bypass this. This is why I always advise removing the Google account before flashing to avoid this issue entirely.

---

Why Do We Need Infinix Note Edge X6887 Firmware?

The Infinix Note Edge X6887 uses a MediaTek chipset, and SP Flash Tool is the standard tool for MTK devices. Here is what flashing the stock firmware accomplishes:

• Unlock your device if it has been locked or disabled.
• Update to the latest Android version supported by your phone.
• Recover your device when it only boots into recovery mode.
• Repair a phone that shuts down randomly or restarts in a loop.
• Fix startup loops, lagging, and freezing on your device.
• Restore the original Infinix stock ROM to keep your warranty valid.
• Recover from “Download DA FAIL” errors and Secure Boot authentication issues specific to the MediaTek chipset in your device.

Read more about stock ROMs and why flashing works here.

---

Which Firmware Version Does Your Infinix Note Edge X6887 Need?

The biggest mistake I see is flashing the wrong firmware variant. Before downloading, verify your device identity:

1. Verify Your Exact Model: In Settings, look for the model code “X6887”. Some Infinix phones share the same marketing name but have different internal hardware.
2. Confirm the Processor: This build targets the MediaTek Dimensity 7100 (MT6858) chipset. You can check your chipset via recovery mode or a hardware info app.
3. Review the Version Number: The firmware version in the download table should be close to or newer than what your device is currently running.
4. Use Recovery Mode as a Safety Check: Before flashing, boot into recovery to see the current build number and chipset printed on screen. This is the most trustworthy check.
5. Verify the Region: Some firmware builds are region-specific. Confirm the download matches your device region or is listed as global.

---

Firmware Details for Infinix Note Edge X6887

Here is a quick overview of the official firmware specifications:

Firmware Information	Details
Device Model	Infinix Note Edge X6887
Firmware Version	16.1.0.115SP09
File Size	9.5 GB
Android Version	Android 16, XOS 16
Platform	MediaTek Dimensity 7100 (MT6858)
Release Date	Released 2026, January 31
Region	Global, Africa and Asia
File Type	ZIP (Includes Scatter File [MT6xxx_Android_scatter.txt], preloader.bin, boot.img, system.img, recovery.img, lk.bin, logo.bin, nvram.img, and more)

---

Which Firmware Version Should I Download?

This is a common question in the comments, so I put together a simple guide. Find your situation in the table and go straight to the right file:

Your Situation	What I Recommend
Phone is completely dead or stuck on logo	16.1.0.115SP09, download this one. It is the latest Infinix Note Edge X6887 firmware available.
FRP / Google account lock only	See the FRP bypass guide above, you likely do not need the full firmware for this.
Phone slow after a recent OTA update	Try the next older version, sometimes the latest OTA introduces new bugs and an older build runs better.
IMEI missing after a previous flash	Re-flash 16.1.0.115SP09 first, then follow the IMEI repair guide. Do not skip the reflash.
16.1.0.115SP09 failed with a flash error	Try the next older version instead and double-check your scatter file selection before assuming the firmware is the problem.
Restoring to factory / warranty repair	16.1.0.115SP09, clean state, fresh start.

My general rule with MTK devices is to try the latest version first. I have seen users waste time on older builds when the newest one works fine. Only try an older version if the latest fails more than once, and ensure it is a driver issue, not a firmware problem.

---

Download Infinix Note Edge X6887 Firmware

Download the official stock firmware for your Infinix Note Edge X6887 below. The latest available version is 16.1.0.115SP09. After downloading, verify the file size matches the table above, a size mismatch usually means a partial or corrupt download, and flashing a corrupt file can cause more problems than it solves.

Software Details	Download Link	Members Link
File Name: Infinix_Note_Edge_X6887_MT6858_16.1.0.115SP09_IN001PF001AZ_010126_MXML.zip Size: 9.5 GB	Download Link	Download Link2

Only download firmware that is fully compatible with your exact device model. See the firmware selection guide above if you are not sure.

Important: The Infinix Note Edge X6887 (X6887) should not be confused with other Note Edge variants that may have different chipsets or regional firmware. Even devices in the same Note Edge line can use completely different processors. Always verify your exact model code “X6887” in Settings > About Phone before downloading any firmware from this page.

---

Infinix Note Edge X6887 Flash Setup Checklist

Do not skip these steps. Most failed Infinix flashes happen because people rush the preparation. The VCOM driver is essential for this device and other MediaTek phones. Windows may show the device in Device Manager, but SP Flash Tool will not detect it without the correct VCOM driver installed.

1. Write Down Your IMEI: Open your phone dialer and type *#06#. Take a photo of the screen showing both IMEI numbers. You may need these later to fix your IMEI if it gets wiped during the flash.
2. Sign Out of Google: Open Settings, go to Accounts, and remove every Google account from the device. If you skip this, Google will lock the phone after flashing and you will need to do an FRP bypass.
3. Save Your Files: Copy everything important to a PC or cloud storage. After flashing, the phone will be completely empty, no apps, no photos, no messages.
4. Battery Check: Charge to at least 50%. If the phone dies during flashing, you could end up with a device that will not turn on at all.
5. Get the Right Cable: You need a USB data cable, the kind that can transfer files, not just charge. Plug it into a USB 2.0 port on a Windows PC for the most reliable connection.
6. Set Up Drivers:
   • VCOM Drivers
   • Infinix USB Drivers

---

How to Install Firmware on Infinix Note Edge X6887

We are using SP Flash Tool for this. For older devices, I recommend trying SP Flash Tool v5.1924 first. The newer versions of SP Flash Tool require a DA (Download Agent) file that older firmware packages do not include, and that is what causes the “Auth” errors you may have seen. If SP Flash Tool keeps asking for an auth file and you do not have one, switch to MTK Client, it handles Secure Boot automatically. Download SP Flash Tool for Windows or SP Flash Tool for Linux and follow the steps below. The complete SP Flash Tool guide is also available if you need more detail.

1. Download the Firmware Package:
   • Use the download links in the table above to get the correct firmware file for your device.
   • Extract the archive with WinRAR or 7-Zip. Use a short folder path like D:flash to avoid issues with some tools.
2. Check Drivers:
   • All drivers from the prerequisites must be installed before connecting your device. Restart your computer after installing them.
3. Load the Firmware File:
   • Click on the “Scatter-loading” button. Navigate to the folder where you extracted the firmware and select the “scatter.txt” file.
4. Connect Your Device:
   • Power off your phone completely, not sleep mode, fully off.
   • Connect to your PC via USB cable. The flash tool will detect it automatically.
5. Start Flashing:
   • Press “Download” to begin writing the firmware to your device.
   • Do not unplug the phone, close the flash tool, or interact with the device until the process is 100% complete.
6. Wait and Reboot:
   • After the tool confirms the flash is complete, safely disconnect your phone.
   • Press the power button to start your device. The initial boot is slow, wait up to 8 minutes before assuming there is a problem.

---

After Flashing: What Happens Next on Infinix Note Edge X6887

Here is what is completely normal after a successful flash:

• How to know the flash was successful: SP Flash Tool will show a green circle or checkmark when done. If you see that, the flash completed successfully.
• Storage will show almost full capacity available since all your apps and files are gone. The system partition size varies by firmware version but is typically 4 to 8 GB on most devices.
• Battery percentage may seem inaccurate for the first day. The battery statistics are calibrated during normal use. Charge the phone fully once without interruption and the readings will stabilize.
• The phone will feel warm during first boot, this is normal. It settles after a few minutes once the initial app setup is complete.
• Dial *#06# immediately after setup to check your IMEI. Do this before you insert a SIM card. If it shows “unknown” or “null”, follow the IMEI repair guide below before doing anything else.
• Be careful when re-adding your Google account, if you did not remove it before flashing, you may see an FRP prompt. Add it fresh during the setup wizard, not afterwards through Settings.
• Fingerprint and face unlock data are erased during the flash. You will need to re-register your fingerprints and face data from scratch in the security settings.

---

Troubleshooting Infinix Note Edge X6887 Flash Errors

1. Infinix Note Edge X6887 Not Recognized by SP Flash Tool:
   • In most cases this is a driver issue, not a cable issue. Reinstall the VCOM drivers for the X6887, restart your PC, and try again before changing anything else.
   • If that does not work, switch to a USB 2.0 port, USB 3.0 ports can cause detection issues with MediaTek devices more often than people expect.
   • Still not working? Temporarily disable your antivirus. It can block the VCOM driver from loading without giving you any error message.
2. Boot Loop After Flashing:
   • Enter recovery mode and perform a factory reset from there. Most post-flash bootloops on MediaTek are caused by conflicts with old cached data, a wipe from recovery usually fixes this without needing to reflash.
3. Wrong Scatter File / Firmware Mismatch:
   • If SP Flash Tool throws an error as soon as you try to start the download, check your scatter file first. A mismatch between the scatter file and your device build is one of the most common causes of flash errors.
4. “Download DA FAIL” Error:
   • This error comes up regularly. It almost always means the VCOM driver is not properly installed. Reinstall it, restart your PC, and try again. If that still does not work, try switching to SP Flash Tool v5.1924, older devices sometimes respond better to the older version.
5. Error 8038 (BROM Error):
   • The device is not entering BROM mode correctly. Power it off completely and, if possible, remove the battery for 30 seconds. Reconnect and try again. Some MediaTek devices require you to hold Volume Down while plugging in the USB cable to enter BROM mode.
6. Auth File / Secure Boot Error in Newer SP Flash Tool:
   • Newer versions of SP Flash Tool require a DA (Download Agent) authentication file for devices with Secure Boot enabled. If you do not have that file, switch to MTK Client instead, it handles Secure Boot automatically and is the simpler solution.

---

Missing IMEI or Corrupt Baseband on Infinix Note Edge X6887 After Flashing?

A missing or unknown IMEI is one of the most common things I see after a MediaTek flash. It happens because the NVRAM partition, which stores your IMEI and calibration data, sometimes does not survive the flash intact. It looks alarming, but it is fixable. Here is what to do:

1. Check your drivers first: Install the Mediatek CDC Driver if you have not already, without it, the IMEI repair tools will not detect your device. This is the step most people miss.
2. Use SN Write Tool or Maui Meta: SN Write Tool is the first option I try, it is straightforward and works on most MTK devices. Maui Meta is the alternative if SN Write does not connect. You can learn more about using SN Write Tool here.
3. Run the repair:
   • Connect your device to the computer.
   • Enter the original IMEI numbers for both SIM slots, these are the numbers you wrote down before flashing.
   • Click “Start” and let it complete without interrupting the connection.
4. Verify after reboot: Once done, reboot your phone and dial *#06#. Your IMEI numbers should be back. If they are still showing null, run the process again, sometimes the first attempt does not complete correctly.

Video Guide: How to repair IMEI

Credits: https://www.youtube.com/@mhgsmclinic

---

Common Questions About Flashing Infinix Note Edge X6887

Q1: Can I flash this firmware if my phone does not turn on at all?
A: Yes, in most cases. As long as the phone responds to a USB connection (even with a black screen), the flash tool can detect it. If the battery is completely drained, charge it for at least 15 minutes first.

Q2: Can I use a Mac or Linux computer for this?
A: The tools and drivers referenced on this page are Windows-only. If you are on Mac or Linux, your best option is to use a Windows virtual machine, or borrow a Windows PC for the 10 minutes it takes to complete the flash.

Q3: What if the flash fails halfway through?
A: Do not panic and do not disconnect the phone. Close SP Flash Tool, restart it, and try the flash again from the beginning. In most cases, a failed flash just means the process needs to be repeated. The device is usually still detectable by the flash tool even after a failed attempt.

Q4: Will flashing erase my data?
A: Yes, flashing with SP Flash Tool restores the device to factory state, including Android 16, XOS 16 default settings. All apps, photos, contacts, and accounts will be removed. Back up everything you need before you start. There is no way to recover data once the flash is complete.

Q5: Can I go back to an older firmware version?
A: It is technically possible on some MediaTek builds, but downgrading can cause security issues and app compatibility problems. If the latest version is causing trouble, leave a comment below, there is usually a better fix than rolling back.

Q6: Do I need an internet connection during flashing?
A: No. The flashing process is entirely offline, it happens between your PC and the phone via the USB cable. You do not need internet at any point during the flash itself. You will need internet later to set up the phone and download your apps.

Q7: What should I do if I encounter an FRP lock after flashing?
A: Use our free Android apps launcher. FRP lock activates when a Google account was still signed in before flashing. This is why signing out of your Google account before flashing avoids this issue entirely.

Q8: How do I enter recovery mode?
A: Power the device off completely, then hold Volume Up + Power at the same time until the recovery menu appears. The recovery menu displays the build number which you can use to verify your firmware version before flashing.

People Also Ask About Infinix Note Edge X6887

What is the latest firmware version for Infinix Note Edge X6887?
The latest available Infinix Note Edge X6887 firmware on this page is version 16.1.0.115SP09. This page has 1 firmware build available for download. Check the firmware details table above for file sizes and Android versions.

Can flashing firmware fix a bricked Infinix Note Edge X6887?
Yes. If your Infinix Note Edge X6887 is stuck on the logo, in a bootloop, or will not turn on, flashing the stock firmware with SP Flash Tool can restore it to working condition. This is the standard repair method used by service centers for Infinix devices.

How do I check my Infinix Note Edge X6887 model number before flashing?
Go to Settings > About Phone on your Infinix Note Edge X6887 and look for the model number “X6887”. You can also confirm by entering recovery mode (Volume Up + Power while powered off) which displays the build number and model code. Always match this exactly with the firmware filename before flashing.

Will flashing firmware on Infinix Note Edge X6887 erase my data?
Yes. Flashing stock firmware on the Infinix Note Edge X6887 with SP Flash Tool performs a full factory reset. All apps, photos, contacts, and accounts will be removed. Back up everything important before you start. There is no way to recover data after flashing.

---

Conclusion

You have just completed a clean firmware flash on your Infinix Note Edge X6887. The device should now be back at the setup wizard on a fresh 16.1.0.115SP09 build.

Questions, errors, or something not covered here? The comments section is open. Tell me exactly what happened and I will walk you through the fix.

If you found this useful, a quick share goes a long way, someone else with the same device is probably searching for this right now.

Browse all Infinix firmware downloads for more devices.

---

Disclaimer: Flashing stock firmware is performed at your own risk. Follow the instructions on this page carefully. I cannot be held responsible for any damage to your device, but I will always try to help if something goes wrong.